Aerial NDT · Okanagan
Pulsed Eddy Current (CUI) in West Kelowna, BC
Corrosion-under-insulation screening through cladding — pulsed eddy current by drone reads wall thickness through up to 100 mm of insulation and weather jacket. No stripping. Flown by Transport Canada-certified RPAS pilots serving West Kelowna and the Okanagan region — since 1999 as BC's leak detection and inspection specialists.
Free phone consult · No pressure · Mon–Sat 8am–6pm PT
Flying West Kelowna: local context
Vineyard estates and wildfire-rebuild neighbourhoods — new roofs needing QA beside legacy stock.
Local asset profile: Vineyard estates, lakeview subdivisions, and rebuild zones from recent fire seasons.
Typical pulsed eddy current (cui) work around West Kelowna
- Rebuild roof QA
- Vineyard building scans
- Insulated piping and vessels (CUI)
- Aluminum-jacketed assets
- Tank insulation systems
How the West Kelowna survey runs
- 1
CUI risk mapping
Operating temperature bands and insulation condition identify the highest-probability CUI zones — screening starts where the odds are worst.
- 2
Through-cladding scan
The PEC sensor reads relative wall thickness through insulation and jacket — up to 100 mm of lift-off — while the asset stays fully dressed.
- 3
Anomaly grading
Wall-loss indications are graded and ranked; clean areas are cleared without a single jacket screw turned.
- 4
Targeted verification
Only graded anomalies get insulation windows opened for direct UT verification — removal budgets shrink to the spots that matter.
West Kelowna questions, answered
What is corrosion under insulation and why is it such a problem?
CUI is external corrosion on insulated piping and vessels, fed by moisture trapped against the steel — invisible until the jacket comes off or the wall fails. It is among the most expensive integrity threats in process industries precisely because finding it traditionally meant stripping and reinstating insulation on spec.
How does PEC see through insulation?
Pulsed eddy current induces a decaying electromagnetic field in the steel through the non-conductive insulation and thin jacket; the decay rate corresponds to remaining average wall thickness. It reads through up to 100 mm of lift-off on 3–18 mm carbon steel walls — screening data with zero removal.
Is PEC a replacement for UT?
No — it is the screening layer. PEC grades relative wall loss through cladding fast; direct UT then quantifies the graded spots through small inspection windows. The pairing typically cuts insulation removal budgets by an order of magnitude versus strip-and-inspect.
What jacket materials can you scan through?
Aluminum and stainless weather jackets over standard insulations are the designed use case. Thick galvanized jackets reduce sensitivity and get flagged at scoping. The aerial platform adds the part rope teams hate: elevated insulated lines and vessel tops without scaffolding.
Can you legally fly drones for inspection in West Kelowna?
Yes — our pilots hold Transport Canada RPAS certification with advanced-operations capability, and West Kelowna operations run under whatever airspace authorizations the location requires. Vineyard estates and wildfire-rebuild neighbourhoods — new roofs needing QA beside legacy stock. Flight planning, NOTAM checks, and authorizations are part of the service, not your problem.
How does West Kelowna weather affect scheduling?
Aerial inspection flies in defined weather windows — wind, precipitation, and (for thermal work) the right temperature differentials. West Kelowna sits in our standing Okanagan coverage, so we schedule against the local forecast and typically land the survey within days of booking rather than weeks. Mon–Sat, 8am–6pm Pacific.
What does pulsed eddy current (cui) cost in West Kelowna?
Province-wide pricing — no regional premium for West Kelowna. Single-asset thermal surveys typically start in the high hundreds; NDT campaigns and multi-asset programs are quoted by scope. The free phone consult (604-239-9934) produces a firm number in about five minutes.
Other aerial services in West Kelowna
Aerial EMAT Inspection in West Kelowna
Electromagnetic acoustic transducer thickness testing by drone — no couplant, up to 4 mm lift-off, made for corroded, dirty, or coated steel where conventional UT struggles.
View serviceAerial High-Temperature UT in West Kelowna
Wall-thickness measurement on hot, in-service assets — 0 to 260 °C (32–500 °F) — without shutdown, by drone. Echo-to-echo and pulsed-echo modes with live A-scan.
View serviceAerial Ultrasonic Testing (UT) in West Kelowna
Contact UT wall-thickness measurement delivered by drone — corrosion mapping on tanks, stacks, and structures at height without scaffolding, rope access, or shutdown.
View serviceAerial Industrial Thermal Survey in West Kelowna
Heat-loss mapping on tanks and pipelines, refractory damage, stack hot spots, and district-energy networks — plant-scale radiometric surveys from the air.
View service← All about pulsed eddy current (cui)·Aerial inspection hub·drone.leak.ca
Aerial Pulsed Eddy Current (CUI) near West Kelowna
Need pulsed eddy current (cui) in West Kelowna?
Free phone consult — asset, access, airspace, and a firm quote in five minutes. No pressure.